Master/Slave Operation

Each 360 degree corner module consists of a "master" and a "slave" driver circuit board, 360 degree optics and LED light

engines along with a single integrated heatsink bracket.

The "master" circuit board (rear position) must always be powered for the "slave"(front position) to flash. The "master" is always

located in the rear position of the module. The lightbar is wired to allow running only the rear facing LED on each module by

removing power to the front facing "slave" module. This gives a "front-cutoff" function. The flash pattern for each corner pair

can be selected by shorting together the 2-pin header J1, on the "master" , momentarily and releasing. The module is set-up

for "Cycleflash" as a standard. Holding down the 2-pin header for 5 sec., or longer, and releasing will return the pattern to

Cycleflash. The following chart describes the available patterns and order;

360 Degree Module Flash Pattern - Table 3

See Figure 22

Both heads will be in the mode selected. Both heads will flash together unless in Front Cut-off mode.

LED DIRECTIONAL MODULES

In addition to the 360 warning modules the lightbar may be equipped with a number of single head

directional warning LED modules. These modules are available in either the existing LED X™ ( 1" X 4" ) or the new Code 3®

OPTIX™ ( 1" X 6" ) and LC-LED directional modules in stationary and flashing versions ( see figure 8). The stationary versions

can be flashed by connecting the module(s) to any flasher that does not require ground through the load (example: Code 3®

700 series relay flasher). The flashing modules will have "Cycleflash" as the standard pattern. The OPTIX and LEDX flash

pattern can be changed by shorting the 2-pin header, J1 as shown in Figure 22, momentarily then releasing. Table 4 shows

the available patterns and the order when stepping through patterns. The module can be reset to "Cycleflash" by shorting the

header for greater than 5 sec. and releasing.

Operating Specifications for directional module:

Operating Voltage: 10-16 VDC, Reverse Polarity Protection

Current Draw : Flashing Module

Red/Amber - .25A avg @ 12.8 Volts

Blue/White - .4A avg @ 12.8 Volts

Steady Burn Module

Red/Amber - .5A avg @ 12.8 Volts

Blue/White - .8A avg @ 12.8 Volts

Available Colors - Red , Blue, Amber, and White

Cycle Flash Cycles through various patterns @ 70 fpm

Five Flash Five Pulses per flash @ 70 fpm

Quad Flash Four Pulses per flash @ 70 fpm

NFPA Four Pulses, 70% Duty Cycle @ 75 fpm

Triple Flash Three Pulses per flash @ 70 fpm

Quad Pop Flash Four Pulses per flash (3 equal, 1 extended) @ 70 fpm

Flash Pattern Description

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 31 32

Comentarios a estos manuales

Sin comentarios

Lennox Hearth SYMMETRY SERIES ANDIRON KITS AKT-DV manuals

Owner’s manuals and user’s guides for Kiln Lennox Hearth SYMMETRY SERIES ANDIRON KITS AKT-DV.
We providing 1 pdf manuals Lennox Hearth SYMMETRY SERIES ANDIRON KITS AKT-DV for download free by document types: User Manual

Lennox hearth SYMMETRY SERIES ANDIRON KITS AKT-DV User Manual (1 pages)

Brand: Lennox-hearth | Category: Kiln | Size: 0.43 MB |

HEARTH PRODUCTS

KITS AND ACCESSORIES

SYMMETRY SERIES ANDIRON KIT

More products and manuals for Kiln Lennox Hearth

Models	Document Type
Bi-Fold Glass Doors 42BFOD-BS	User Manual Lennox Hearth Bi-Fold Glass Doors 42BFOD-BS User Manual, 4 pages
DAVE LENNOX SIGNATURE COLLECTION LSS-CA35	User Manual Lennox Hearth DAVE LENNOX SIGNATURE COLLECTION LSS-CA35 User Manual, 2 pages
END PANEL ASSEMBLY 38AEP-BS	User Manual Lennox Hearth END PANEL ASSEMBLY 38AEP-BS User Manual, 2 pages
EST-48-H	User Manual Lennox Hearth EST-48-H User Manual, 8 pages
B-MNC0353VDE	User Manual Lennox Hearth B-MNC0353VDE User Manual, 32 pages
E36ODG	User Manual Lennox Hearth E36ODG Manuel d'utilisation, 2 pages
ADAGIO-AG	User Manual Lennox Hearth ADAGIO-AG User Manual, 2 pages
DIRECT-VENT SYMMETRY SERIES SYM-35N	User Manual no-title, 28 pages
Elite CVF-NG	User Manual Lennox Hearth Elite CVF-NG User Manual, 18 pages
EDVI25	User Manual Lennox Hearth EDVI25 User Manual, 24 pages
ELITE ELDV-40NM	User Manual Lennox Hearth ELITE ELDV-40NM User Manual, 40 pages
ELITE SERIES LBC-3824	User Manual Lennox Hearth ELITE SERIES LBC-3824 User Manual, 20 pages
BRENTWOOD LV	User Manual Lennox Hearth BRENTWOOD LV User Manual, 30 pages
Electronic LMDV-3530-CNM	User Manual Lennox Hearth Electronic LMDV-3530-CNM User Manual, 36 pages
LENNOX MPE-33R	User Manual Lennox Hearth LENNOX MPE-33R User Manual, 20 pages
Crestline LSBV-3628MP-H	User Manual Lennox Hearth Crestline LSBV-3628MP-H User Manual, 24 pages
X-FIRES-1000-LP	User Manual Lennox Hearth X-FIRES-1000-LP User Manual, 24 pages
INTERTEK LMBV-42REN	User Manual Lennox Hearth INTERTEK LMBV-42REN User Manual, 20 pages
Brentwood SP	User Manual Lennox Hearth Brentwood SP User Manual, 24 pages
Crestline LSBV-3628MN	User Manual Lennox Hearth Crestline LSBV-3628MN User Manual, 20 pages

Code-3 MX 7000 Manual de usuario Pagina 10

Comentarios a estos manuales

Lennox Hearth SYMMETRY SERIES ANDIRON KITS AKT-DV manuals

Lennox hearth SYMMETRY SERIES ANDIRON KITS AKT-DV User Manual (1 pages)

Table of contents

More products and manuals for Kiln Lennox Hearth

Code-3 MX 7000 Manual de usuario Pagina 10

Comentarios a estos manuales

Relacionado con productos y manuales para Encendiendo Code-3 MX 7000

Lennox Hearth SYMMETRY SERIES ANDIRON KITS AKT-DV manuals

Lennox hearth SYMMETRY SERIES ANDIRON KITS AKT-DV User Manual (1 pages)

Table of contents

More products and manuals for Kiln Lennox Hearth