Code-3 Volt Manual de usuario descargar pdf (Pagina 2)

920-0211-00 Rev. A Page 2 of 3

Operation:

After installing the system it is best to do a POWER-UP RESET the rst time to ensure that all heads are in sync. Touch BLUE wires to +V (RED wire) while

applying power. Wait 1 second and then release the BLUE wires. All heads will reset to Pattern #2. (If you have installed a pattern select pushbutton, press

and hold pattern select while turning power switch ON.) To select a ash pattern, touch BLUE to +V or press pattern select switch to increment the ash

pattern. The heads will remember the ash pattern you have selected until it is changed again. When you increment past pattern #16 it will roll back around to

pattern #1.

Flash patterns 9 to 16 in the ash pattern list run through the patterns

listed in a continuous cycle.

If you are using this product to synchronize with an older product which only has ash patterns 1 through 8 then you may program this product to limit it’s ash

pattern list. Perform the following: Connect BLUE to RED (or press and hold pattern select button if installed. Connect to power and hold for 5 seconds. The

LED head will blink 1 time to indicate it is set for the old 8 pattern set, twice to indicate the 16 pattern set.

Surface Mounting:

Mark and drill mounting hole locations in mounting surface. Make the

electrical connections described below and feed the driver module through

the mounting hole. Silicone RTV sealant should be used around the

mounting and screw holes. Install the bezel using the two screws provided.

SURFACE MOUNTING

DO NOT USE LED HEAD

WITHOUT DRIVER MODULE!

0.575”

[14.61]

1.65”

[41.91]

DRIVER MODULE

MOUNTING SURFACE

0.688”

[17.46]

1.8”

[45.72]

0.094”

[2.38]

2.27”

[57.66]

BEZEL

SCREWS

MOUNTING HOLE

BEZEL OUTLINE

3/32” DRILL

FIGURE 2

LAMP MOUNTING

DO NOT USE LED HEAD

WITHOUT DRIVER MODULE!

3.12”

[79.25]

0.345”

[8.75]

1.505”

[38.23]

0.175”

[4.45]

0.695”

[17.65]

DRIVER MODULE

1.0”

[25.40]

1.28”

[32.51]

0.094”

[2.38]

SCREWS

GASKET

MOUNTING

SURFACE

MOUNTING HOLE

3/32” DRILL

The LED heatsink will get hot during

operation but will NOT melt any of the

plastic parts of the lens assembly.

DO NOT TOUCH the heatsink

during operation.

FIGURE 1

Lamp Mounting:

Pick a location in the vehicle lamp housing that is at least 1” away from any

existing bulbs. Drill 1” hole in vehicle lamp reector housing with hole saw.

Mark the two screw hole locations and drill with 3/32” bit. Install the LED

head into lamp housing with gasket as shown in Figure 1. Use silicone RTV

on the screws to seal the threads.Strap the driver module to a nearby wire

harness or body structure. Make electrical connections as described below.

Electrical Connections:

RED: Connect to +V through an ON/OFF switch. The use of a fuse located close to the voltage source is recommended. Size the fuse according to the

number of heads used in the system. 18AWG or larger wire is recommended.

BLACK: Connect to - GROUND vehicle chassis. 18AWG or larger wire is recommended.

BLUE: Flash pattern SYNC and SELECTION wire. If you wish to have all the LED heads synchronize their ash timings and patterns with each other then all

the BLUE wires must be connected together. (64 Heads Maximum) The BLUE wire is also used to select the ash pattern. Touch the BLUE wire to +V to

select the next pattern in the FLASH PATTERN LIST. The BLUE wire can also be run to a momentary push-button located on the dashboard to allow the

ash pattern to be changed when desired. Note: Do not connect the BLUE wire to - Ground. It will disrupt the ash pattern sync signal.

YELLOW: Alternating / Simultaneous selection. Connect to either +V or GROUND (GND).

The YELLOW wire makes the head re AT THE SAME TIME or ALTERNATING with the other heads in the system.

Heads with YELLOW connected to +V re at the same time. Heads with YELLOW connected to GND re at the same time.

Heads with YELLOW connected to +V will ALTERNATE with heads that have YELLOW connected to GND.

The YELLOW wire has no function in STEADY ON mode.

INSTALLATION OF 4 HIDE-A-LED™ USING PATTERN SELECT SWITCH PANEL (OPTIONAL) ON DASHBOARD.

1 2 3

Comentarios a estos manuales

Sin comentarios

Code-3 Volt Manual de usuario Pagina 2

Comentarios a estos manuales

Relacionado con productos y manuales para Encendiendo Code-3 Volt