Introduction

The TRIUMPH™ (Patent-Pending) Light bar Features the truly unique, SIRIS™ (Patent-Pending) Technology which constitutes a quantum leap for-

ward in signal brightness far exceeding the intensity and quality of any system. The low prole and aerodynamic lines reduce air drag, which results

in fuel savings and stability at high speeds. The TRIUMPH light bar also has an extruded internal frame that is 2X stronger, shock-resistant polycar-

bonate lenses with an intermolded solar barrier, and warning signals that exceed SAE standards.

Unpacking & Pre-Installation

Carefully remove the light bar and place it on a at surface, taking care not to scratch the lenses or damage the cable coming out of the bottom.

Examine the unit for transit damage, broken lamps, etc. Report any damage to the carrier and keep the shipping carton.

The use of this or any warning device does not ensure that all drivers can or will observe or react to an

emergency warning signal. Never take the right-of-way for granted. It is your responsibility to be sure you can

proceed safely before entering an intersection, driving against trafc, responding at a high rate of speed, or

walking on or around trafc lanes.

The effectiveness of this warning device is highly dependent upon correct mounting and wiring. Read and

follow the manufacturer’s instructions before installing or using this device. The vehicle operator should insure

daily that all features of the device operate correctly. In use, the vehicle operator should insure the projection

of the warning signal is not blocked by vehicle components (i.e.: open trunks or compartment doors), people,

vehicles, or other obstructions.

This equipment is intended for use by authorized personnel only. It is the user’s responsibility to understand

and obey all laws regarding emergency warning devices. The user should check all applicable city, state and

federal laws and regulations.

Code 3, Inc., assumes no liability for any loss resulting from the use of this warning device.

Proper installation is vital to the performance of this warning device and the safe operation of the emergency

vehicle. It is important to recognize that the operator of the emergency vehicle is under psychological and

physiological stress caused by the emergency situation. The warning device should be installed in such a

manner as to: A) Not reduce the output performance of the system, B) Place the controls within convenient

reach of the operator so that he can operate the system without losing eye contact with the roadway.

Emergency warning devices often require high electrical voltages and/or currents. Properly protect and use

caution around live electrical connections. Grounding or shorting of electrical connections can cause high

current arcing, which can cause personal injury and/or severe vehicle damage, including re.

PROPER INSTALLATION COMBINED WITH OPERATOR TRAINING IN THE PROPER USE OF

EMERGENCY WARNING DEVICES IS ESSENTIAL TO INSURE THE SAFETY OF EMERGENCY

PERSONNEL AND THE PUBLIC.

WARNING!

Installation & Mounting

Standard light bars are built to operate on 12 volt D.C. negative ground (earth) vehicles. If you have an electrical system other than 12 volt D.C.

negative ground (earth), and have not ordered a specially wired light bar, contact the factory for instructions.

Test the unit before installation. To test, touch the black wire to the ground (earth) and the other wires to +12 volts D.C., in accordance with the

instructions attached to the cable (an automotive battery is preferable for this test). A battery charger may be used, but note that some electronic op-

tions (ashers, etc.) may not operate normally when powered by a battery charger. If problems occur at this point, contact the factory.

Utilizing non-factory supplied screws and/or mounting brackets and/or the improper number of

screws or modifying the supplied parts may result in loss of warranty coverage on the equipment.

WARNING!

1 2 3 4 5 6 7 ... 15 16

Comentarios a estos manuales

Sin comentarios

Zanussi ZFC62/23FF Handbücher

Bedienungsanleitungen und Benutzerhandbücher für Kühlschränke Zanussi ZFC62/23FF.
Wir stellen 2 PDF-Handbücher Zanussi ZFC62/23FF zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung

Zanussi ZFC62/23FF Bedienungsanleitung (17 Seiten)

Marke: Zanussi | Kategorie: Fridges | Größe: 0.23 MB |

Inhaltsverzeichnis

REFRIGERATOR

ZFC 62/23 FF

CONTENTS

TECHNICAL SPECIFICATIONS

WARNINGS

CONSERVATION

INSTALLATION

THE ELECTRICAL CONNECTIONS

DOOR REVERSIBILITY

YOUR APPLIANCE

OPERATION

HEALTH AND SAFETY GUIDELINES

Fresh food refrigeration

Dual purpose meat box

Positioning the door shelf

Drink dispenser

Cleaning the filter

Starting the appliance

Cool check temperature guide

Defrosting

MAINTENANCE AND CLEANING

Exclusions

Zanussi ZFC62/23FF Bedienungsanleitung (18 Seiten)

Marke: Zanussi | Kategorie: Fridges | Größe: 0.36 MB |